Filed Under : 
Sep.23,2011
The Frommer Stop can be a real hassle to tackle without proper instruction. We took one apart half blind so you don’t have to. Read below for step by step instructions on how to field strip this tiny Hungarian monstrosity.
Section I: The Field Strip
Parts Guide:
- Pistol Body
- Magazine
- Barrel Nut Retainer
- Barrel Nut
- Barrel Guide
- Recoil Spring
- Recoil Spring Guide
- Barrel
- Cocking Knob/Bolt Body
- Bolt Head
1. Remove the Magazine Clear the chamber. Safety first!
2. Depress the Barrel Nut Retainer. Some sources suggest using the corner of the magazine. We personally recommend a slim nylon punch.
CAUTION! The Recoil Spring is behind this retainer and under pressure. Hold the top of the now exposed Barrel Guide with your thumb until directed otherwise.
4. Grip the Cocking Knob and cock the pistol. It should lock open.
5. Still holding the Barrel Guide at the top, use your punch to gently pop it out. CAUTION! Again, this is under pressure and be prepared to have the spring bear against your thumb. Release the pressure slowly on the Barrel Guide and let the Recoil Spring out.
7. The Barrel and Bolt Body are now pressed together. Because this is a Long Recoil gun the bolt won’t move home until the barrel is all the way forward. Hold the Cocking Knob and push/pull the Barrel all the way forward. Then let Bolt Body slide back forward. Some may note that this and step 5 are unnecessary and are not in other instructions. I assure you that the extra steps beat losing an eye or chasing the Barrel Nut Retainer across the room when that spring lets loose.
9. The Barrel Guide has a notch at the top for use on the Recoil Spring Guide tip. Use it to depress and rotate the Recoil Spring Guide 1/4 turn. When you depress a nub will project at the rear of the gun at the top of the Cocking Knob. When you release the Recoil Spring after turning, this nub should recess into the pistol. If it is still projecting you have either over turned or not turned far enough.
10. Pull the Bolt Body and Barrel to the rear and out of the pistol. You may pull the Bolt Body and Barrel apart.
12. Depress and rotate the Recoil Spring Guide for another 1/4 turn to release it.
Pull the bolt head out and rotate a bit to line up the lug before returning to the bolt body
Depress the bolt catch with a small screwdriver or other slim tool when replacing the barrel and bolt body into the pistol
Section II: The Complete Disassembly
- Frame
- Magazine
- Barrel Nut Retainer
- Barrel Nut
- Barrel Guide
- Recoil Spring
- Recoil Spring Guide
- Bolt Return Spring
- Barrel
- Bolt Body
- Bolt Head
- Extractor
- Firing Pin
- Firing Pin Spring
- Grip
- Grip Screw
- Hammer
- Hammer Spring and Plunger
- Hammer Pin
- Grip Safety
- Grip Safety Spring
- Grip Safety Pin
- Lanyard Loop
- Magazine Catch
- Magazine Catch Pin
- Trigger
- Trigger Pin
- Trigger Spring
- Trigger Bar
- Trigger Bar Pin
- Disconnector Pin
- Bolt Catch
- Bolt Catch Pin
- Sear
- Sear Spring
- Sear Pin
How to completely disassemble the Frommer Stop:
1. Gently, gently pry up the Extractor with a small screwdriver. Try to keep even pressure against its whole length. As it rises you can rotate carefully clock-wise and pull it free of the Bolt Head. CAUTION! The Firing Pin and Firing Pin Spring are contained inside under pressure. They will be released when the Extractor is pulled out. Make sure to point them somewhere safe and padded.
2. If they have not flown free, pull out the Firing Pin and fish out the Firing Pin Spring.
3. Unscrew the Grip Screw. Be careful to check on the other side. The Grip Screw is threaded into a nut attached to the left side grip. It may have come loose and may free spin in the Grip. If this is the case you’ll need to find a way to anchor the nut. Then remove the Grip.
4. Hold the Hammer, pull the Trigger, and ease the Hammer forward gently.
5. Drift out the Hammer Pin. You may now remove the Hammer and the Hammer Spring and Plunger.
6. Drift out the Grip Safety Pin. You may now remove the Grip Safety, Grip Safety Spring, and Lanyard Loop.
7. Drift out the Magazine Catch Pin. You may now remove the Magazine Catch.
8. Drift out the Trigger Pin and then the Trigger Bar Pin. You may now remove the Trigger Bar rearward. This may be snug in the Trigger and require a fair about of wiggling and pulling. Remove the Trigger forward.
9. Drift out the Disconnector Pin.
10. Drift out the Bolt Catch Pin and remove the Bolt Catch from the rear of the Frame.
11. Drift out the Sear Pin and remove the Sear and the Sear Spring from the inside of the Frame through the grip area.
12. The ejector spring set in the barrel has a very likely chance of snapping if removed and should be left alone unless absolutely necessary.
Your Frommer Stop is now fully disassembled!
Reassembly tips:
Go Slow
Replace the sear and drive its pin, then place the sear spring on top, then lower the bolt catch down on top of it and push into place with your pinky and hold. Now drop in the pin.
When driving the disconnector pin, the flat side goes up.
Replacing the trigger is a butt. Replace just the trigger and drive its pin in place. Now set the trigger bar (lots of shoving) and line it up. You’ll probably notice you lack the necessary clearance to drive the trigger bar pin. If so, drift the trigger pin back out, set the trigger bar, push the spring in, then reset the trigger. Yeesh!
Lining up the grip safety was the hardest part for us. Getting it and the lanyard loop in the right spot at the same time isn’t easy. Use a zip tie around the frame’s grip area to compress the safety and use a pilot pin to keep things lined up as you drive the pin back in.
Tags : .32ACP, disassembly, Hungary, Pistol
